Reversible knives have two to four cutting edges, when the blade becomes dull, just loosen the screw fastening the blade, rotate and retighten it, so as to save working time and do not need to re-clamp the tool, another important feature of the reversible knives is that it has no wear of blade edge and strictly ensures the tolerance.
UKO’s woodworking carbide reversible knives are high-performance, use solid carbide micro-grain tips give superior tool life in a wide variety of materials for all general joinery in hardwoods and softwoods.
Wood Cutting Tools Carbide Reversible Knives, Indexable Knives Suitable for Different Cutting Heads and Spiral Planning Cutter.
We use advanced ANCA five-axis CNC machine production, plus experienced engineer design, strict quality control management system, to ensure that our product accuracy is high, quality, and maximize your production benefits.
Woodworking circular saw blade is the most commonly used tool for wood products processing, but not all wood products are processed with the same woodworking circular saw blade. It is said that each lock corresponds to only one key, so different materials of wood require different Woodworking circular saw blade. There are many parameters involved in woodworking saw blades, such as: the choice of alloy type, base body, diameter, tooth number, thickness, and so on. The following tells you how to use these parameters correctly and reasonably to select the appropriate woodworking circular saw blade.
The first is the choice of alloy types. Commonly used types of cemented carbide are tungsten-cobalt (code YG) and tungsten titanium (code YT). Because tungsten-cobalt-based cemented carbide has better impact resistance, it is more widely used in the wood processing industry. The commonly used model in wood processing is YG8-YG15. The number after YG indicates the percentage of cobalt content. As the cobalt content increases, the impact toughness and bending strength of the alloy will increase, but the hardness and wear resistance will decrease. Choose according to the actual situation.
Then there is the choice of diameter. The diameter of the circular saw blade is related to the sawing equipment used and the thickness of the sawing workpiece. The diameter of the saw blade is small, and the cutting speed is relatively low; the large diameter of the saw blade has higher requirements on the saw blade and sawing equipment, and the sawing efficiency is also high. The outer diameter of the saw blade is selected according to different circular saw machine models to use the saw blade with the same diameter. The diameters of standard parts are: 110MM (4 inches), 150MM (6 inches), 180MM (7 inches), 200MM (8 inches), 230MM (9 inches), 250MM (10 inches), 300MM (12 inches), 350MM ( 14-inch), 400MM (16-inch), 450MM (18-inch), 500MM (20-inch), etc. The diameter of woodworking saw blades is mostly designed between 120MM-400MM.
The second is the choice of the number of teeth. Generally speaking, the more the number of teeth, the more cutting edges can be cut per unit time, and the better the cutting performance. However, more cutting teeth require more cemented carbide and the price of the saw blade High, but the saw teeth are too dense, and the chip volume between the teeth becomes small, which is easy to cause the saw blade to heat up; in addition, there are too many saw teeth. When the feed amount is not matched, the amount of cutting per tooth is small, which will increase the friction between the cutting edge and the workpiece , Affect the service life of the blade. Usually the tooth spacing is 15-25mm, and a reasonable number of teeth should be selected according to the material to be sawed.
The choice of woodworking circular saw blade requires reference of various parameters. In addition to the several parameters described above, there are some others, such as: thickness selection, tooth profile selection, aperture selection, etc. These parameters determine the saw blade The processing ability and cutting ability, and the choice of woodworking circular saw blades just affects your work efficiency and work results, and has a great impact on improving product quality and shortening working time. The above is about how to choose the right woodworking circular saw blade.
How To Make the Saw Teeth Sharp Again?
For any piece of circular saw blade, no matter where it is born or what material it is made of, they cannot avoid the fate of wear. Among the large family of saw blades, even high-performance multi-blade tools such as diamond saw blades、carbide saw, still need to bow their heads in the face of wear. The only difference may be that the wear occurs later.
In fact, the wear of saw blades has always been a headache for saw blade manufacturers and material sawing and processing companies. For producers, although they know that the market has very high expectations for the life of saw blades. But according to the current technical level and material technology, the saw blade manufacturer can be said to be powerful and has nowhere to use it. When faced with the endless chatter about the life cycle of buyers, they can only reply with consumables, and it is difficult to guarantee the use time as a reply.
From the standpoint of saw blade users, the high loss rate and high scrap rate actually mean that companies have to spend more money on purchases. Once the scale of the enterprise increases and the amount of saw blades increases, the problem of saw blade wear will eventually become an issue.
Judging from the above-mentioned interests of both parties, no one wants to have a very short life of the saw blade produced or in use. But the reality is that the wear of the saw blade is everywhere and occurs all the time. Many people think that only when the saw blade is in working condition, the saw blade will wear out. But in fact, even when the saw blade is in a non-working state, the wear of the saw blade will also occur.
From the perspective of the manufacturing process of a circular saw blade, whether the heat treatment process of the saw blade substrate passes the test, the technical level of the welding teeth, and whether the packaging and transportation can be fast and stable are all the links that will appear in the non-use stage of the saw blade. . Take the transportation of saw blades as an example. Wrong placement of saw blades and violent saw blade transportation will cause the saw blades to undergo changes in stress, and even the problems of tooth loss and wear during the transportation process.
Therefore, if a circular saw blade can be used for a long time, it is far from enough to rely on standard operation. On the contrary, from production to transportation, and then to use, any link cannot be ignored.
After a saw blade is actually working, as the amount of sawing tasks increases, the degree of wear of the saw blade itself will continue to deepen. Among them, mechanical impact wear and thermal wear are the two major causes of saw blade wear. Once the above-mentioned wear and tear are allowed to develop, the company’s own sawing cost is bound to be substantially increased invisibly. The final result is a decline in annual profitability.
Frankly speaking, we cannot avoid the wear of the saw blade. But after the saw blade is really worn, we can still make a difference, and then make the saw blade that is about to be scrapped “the sword is not old and returns to the edge.” According to the existing technology, in order to effectively make the worn saw blade be To use it efficiently, the most effective method is undoubtedly to sharpen the saw blade.
From the perspective of the saw blade grinding process, when a worn saw blade is sent to a professional saw blade manufacturer. Relevant grinding manufacturers will grind the saw blade at multiple levels and in all directions. It ranges from the leveling of the saw blade base to the fine grinding of the front angle, back angle and side angle of the saw blade. The complete set of saw blade grinding process reaches 18 steps.
After the above-mentioned multiple saw blade grinding processes, the performance of the ordinary carbide circular saw blade will be restored to the cutting performance of the new blade. It is imperative for the sawtooth to return to sharpness. For those saw blades with a very good foundation, such as high-performance multi-edged tools such as diamond saw blades, not only can they be sharpened more often than ordinary carbide saw blades, but the grinding effect is also better. good.
Of course, not all saw blades are suitable for grinding, for those with a very high degree of wear. For example, saw blades with large-scale tooth loss, or even saw blades with cracks in the substrate, basically lose the need for grinding. Therefore, for those companies that do not understand saw blade grinding, before trying to establish a cooperative relationship with saw blade grinding manufacturers, it is very necessary to ask whether their saw blades are likely to be repaired.
What are the common problems of woodworking circular saw blades?
What is the difference between the professional and ordinary woodworking circular saw blades?
Chinese brands can adequately meet the needs of diy use. The distinction between grades is the difference in durability, which is the service life, and also involves the production process, such as whether the thickness of the saw body is uniform, the concentricity of the outer circle and the inner circle, and the serrated The quality of the welding process seems to be very simple to make the saw blade, but it is difficult to do it well. For the user, the Chinese product technology is good enough, even for the big brands in Europe and the United States, a large part of it is produced in China. Yes, the staggered teeth are cut wood, and the ladder flat teeth are cut aluminum alloy.
How to define the specifications of woodworking circular saw blades?
Outer diameter-inner diameter-tooth thickness-number of teeth,
The label 210*30*2.0*45 means: the outer diameter is 210 mm, the inner diameter is 30 mm, the tooth thickness is 2.0 mm, and the number of teeth is 45 teeth.
What power tools can woodworking circular saw blades be used for?
Electric circular saws and table saws can be used. Of course, they cannot be used indiscriminately. The following conditions must be met:
The outer diameter of the saw blade must meet the maximum value of the electric circular saw;
The inner diameter of the saw blade must be consistent with the saw blade pressing plate, otherwise there will be problems such as failure to install or slip, the most important thing is that the saw blade must be consistent with the product.
Is there a distinction between left and right for woodworking electric circular saw blades?
It must be installed in the direction of the arrow marked on the woodworking electric circular saw blade, and the saw blade cannot be installed backwards.
Make sure that the direction of the saw blade is consistent with the direction of rotation of the saw blade (the arrow on the saw blade should point in the same direction as the arrow on the circular saw).
The inner pressure plate boss has a diameter of 30 mm on one side and 20 mm on the other side. Use the correct side according to the hole diameter of the saw blade you want to use. Incorrect installation may cause dangerous vibrations.
How to sharpen circular saw blades?
Note that the front-to-back ratio is 1: 3, The minimum remaining length and width of the tungsten carbide saw blade measured from the tooth seat must not be less than 1mm; it must be performed strictly in accordance with relevant operations, non-professionals cannot operate, and the correct method for repair The saw blade can only be used within a reasonable life span if it is not sharpened. If it is not properly ground, it will only reduce the efficiency and quality of the circular saw blade.
It is strictly forbidden to grind only from the front corner surface or only from the rear corner surface. This will greatly shorten the service life of the circular saw blade and also affect the next grinding status! Another important point is that the entire wear area should be fully sanded. The circular saw blade is ground on an automatic sharpener. If it is manually ground on a general-purpose sharpener, it will seriously affect the quality of use.
(The CNC sharpening machine can ensure that the grinding of the front corner surface and the rear corner surface is completely in the same direction.) In order to prevent large wear on the grinding wheel, it is necessary to leave sufficient side protrusions from the side of the sawtooth to the saw body. On the other hand, the largest side protruding part should not be greater than 1.0-1.2 mm on each side to ensure the stability of the saw blade teeth.
Try to ensure the space for chip removal, and avoid the situation that the chip groove needs to be repaired at the same time due to the grinding of the saw teeth.
If the tooth breaks down, you must go to the grinding center to change the teeth. When welding, pay attention to the appropriate welding sound or another solder, preferably with a high-frequency welding machine.
Leveling and stressing
If you want to use a circular saw blade to ensure its quality, you must use the leveling and stressing procedures. Do not use it because of trouble. Each time you grind, check the blade’s flatness and stress value. ? And correct. Leveling can reduce the tolerance of the blade’s runout, and add stress to the strength and elasticity of the blade. This is an essential process for thin saw blades; the relationship between the outer diameter of the circular saw blade and the outer diameter of the flange It can be found in the DIN8083 standard; the outer diameter of the flange should not be less than 25-30% of the outer diameter of the circular saw blade.
Analysis of the grinding effect of cemented carbide saw blades for circular saw blades
Under normal circumstances, most circular saw blades on the market can be ground after a certain period of time. The main purpose is to repair the teeth, make them sharper, maintain the stability of the saw and the quality after cutting, such as carbide saws. Tablets can generally be ground one to three times. The specific number of times depends on the actual use.
There are several ways for the grinding of cemented carbide saw blades, but generally, all use alloy wheels for grinding, and what we are concerned about is the quality after grinding, that is, the use after repairing;
Effect analysis: According to the practical situation, we can judge that the user is most concerned about after grinding:
1. Service life
Effect analysis: After grinding the carbide saw blade, will the service life be reduced compared to the previous one? This will be directly linked to the subsequent cost and benefits of the user. The answer is yes, but if the grinding process is very good, it can reach 70% of the previous time, or even higher. This requires the user to inspect the grinder. Be sure to find a regular and experienced manufacturer for grinding operations.
2. Cut off quality
Analysis of the effect: The quality of workpiece cutting is a responsibility to the market and customers. If the carbide saw blade is ground, the quality of the workpiece is reduced, which is a very unoptimistic thing, which will affect the business of the enterprise. Development, if the customer is not satisfied with the quality, then the subsequent grinding is not necessary at all; in view of this situation, in fact, the user does not have to worry too much, under normal circumstances, the grinding of the carbide saw blade will not affect The original purpose of cutting the quality of the workpiece is to maintain the sharpness of the sawtooth and the quality of the cutting. As long as the user chooses the grinding, do not choose a small processing workshop or an informal enterprise. Generally, the core of quality can be guaranteed;
3. Stability when sawing
Effect analysis: Regarding the stability, unless it is a very poor grinding process, there will be no impact on the stability of the carbide saw blade after grinding.
What are the woodworking circular saw blades? How is it classified?
Classification of saw blades
I. Classification according to different materials: high-speed steel saw blades (HSS saw blades), overall hard alloy saw blades, tungsten steel saw blades, toothed alloy saw blades, diamond saw blades, etc.
2. Classification according to the application: milling cutter blades, machine blades, manual saw blades, metal special saw blades (aluminum saw blades, copper cutting blades, stainless steel saw blades, etc.), pipe cutting circular saw blades, wood Saw blades, stone saw blades, acrylic saw blades, etc.
3. Classification of surface coating: white steel saw blade (natural color), nitrided saw blade (black), titanium-plated saw blade (gold), chromium nitride (color), etc. 4. Other classifications and titles: cutting saw blades, cutting saw blades, grooving saw blades, cutting saw blades, overall saw blades, incisive saw blades, ultra-thin saw blades.
How to install woodworking circular saw blades?
Before installing the circular saw blade, first check the teeth for defects, shedding, abnormal wear, and bending, twisting and cracking of the saw disk. During installation, ensure that the rotation direction of the saw blade is consistent with the rotation direction of the main shaft of the machine
In addition, please pay attention to confirm that the selected saw blade is suitable for the speed and feed of the material being cut. ;
Every time you install the flange, you must ensure that the surface of the flange is flat and clean, parallel to each other and perpendicular to the axis, and the size must be the same. The minimum diameter of the flange is 1/3 of the diameter of the saw blade, and the gasket should be vertical;
The height of the saw blade should be at least equal to the height of the saw blade. When processing, the saw blade should be at least 3 teeth at the same time, otherwise the saw blade will sway.
What is pcd saw blade chipboard saw blade?
PCD saw blades, or diamond saw blades, are typical representatives of superhard tools. The PCD saw blade has a Vickers hardness of 10000HV, strong acid resistance, and the blade is not easy to passivate. As a typical representative of super-hard cutting tools, PCD diamond saw blades lead the woodworking dry cutting operation. Woodworking machinery cutting processing operations to improve production efficiency and production quality, high-quality PCD saw blades are essential.
Science and technology as the first productive force is the biggest driving force for innovative technology and new products. The application of PCD saw blades as super-hard tool materials have always been a high-quality performance of science and technology.
The PCD saw blades produced by our company are made of high-quality alloy steel as the base, and the composite diamond cutter heads with excellent performance are simultaneously formed by electro-discharge mechanical electrolytic grinding technology. The well-designed dynamic balance and scientifically created heat dissipation solve the continuous long-life cutting of the woodworking machinery production line. It is a powerful wealth cutting tool for particleboard, high and medium density board, and high-speed super-finishing.
As the basis of excellent performance, the field test standard can be used continuously for 300-400 hours; strong wear resistance can be re-grinded for many times. It is configured for precision electronic saws and sliding table saws. The maximum scrap time can reach 4000 hours/piece. This provides strong product technical support for carpentry operations, saves many troubles to replace the tool, and minimizes the production cost of the enterprise.
Durability and durability are the advantages of PCD diamond saw blades compared to carbide saw blades. The actual customer test effect of Zhuzhou UKO PCD saw blades exceeds 40-50 cemented carbide saw blades, which provides strong product and service support for the long-term continuous operation of woodworking dry cutting operations.
For woodworking cutting operations, cross-cutting, longitudinal sawing, sawing wooden composite materials, sawing non-ferrous metals, sawing metals, sawing picture frames, sawing plexiglass, sawing hard plastics, sawing veneers, veneers Grooving and grooving with wood composite materials are all manifestations of high-quality cutting performance.
For softwood, hardwood, MDF, non-ferrous metal, square tube, plywood, profile, single veneer, veneer, aluminum, angle iron, double veneer, picture frame, plastic, round tube, particleboard, organic glass, etc. Cutting operations have good performance.
How to understand the stickers on carbide CNC inserts boxes?
The packaging of carbide inserts usually has a lot of information […]
The precision journey of the tungsten carbide inserts
Even under severe conditions (such as complex cutting and deep cavity) […]
How to understand the model of carbide inserts?
There are many CNC carbide inserts of various shapes, uses and materials […]
Use cermet Inserts to save customers half of their costs
UKO introduced cermet insert, it always advocated that cermet can help mold processing […]
WE PROVIDE COMPETITIVE CARBIDE TOOLS FOR OUR CUSTOMERS WORLDWIDE.
ADD No.500 Jinshan Industrial Park, Hetang District, Zhuzhou City.
TEL +86 731 2882 1507